Friday, September 27, 2019

SC Hydraulic Engineering


SC manufactures a variety of products, with some able to reach liquid pressures of 65,000 psi or gas pressures exceeding 17,000 psi:

  • Air operated liquid pumps
  • Air Boosters and Systems
  • Gas Boosters and Systems
  • Power Units
  • High Pressure Stainless Steel Valves

SC Air Operated Liquid Pumps

1. L3 and L3C Series Liquid Pumps

These are more compact than other liquid pumps available. They are air operated with pressure capable of exceeding 18,000 psi. Wetted sections are available in stainless steel and carbon steel. They can be used with de-ionized water, nitrous oxide, and carbon dioxide. Remote pilot and hand pump options are available. 

Common applications:



General Information:

Air Drive

Require no electrical power. Powered by pressurized air, nitrogen vapor, or natural gas. The air drive psi supplied is translated to output pressure using the pressure ratio. If the pressure ratio of the pump is 20:1 and air drive pressure supplied is 50 psi, this means the output pressure is approximately 1,000 psi. A hand pump attachment option is available for precise pressure control or great for applications where shop air is not available.

L3 & L3C ratios available: 20:1, 31:1, 40:1, 55:1, 79:1, 123:1, 133:1, 213:1

  • Starting air drive pressure: < 15 psi
  • Max air drive pressure: 125 psi (intermittent duty)
  • Max output pressure: 24,375 psi at 125 drive psi, 1.0 gpm flow rate
Operation

These pumps operate using the principle of differential areas. A small diameter hydraulic plunger is driven by an air piston and provides a pressure ratio that determines the maximum output pressure.

Cycle

When air is first supplied to the pump, the pump will cycle at maximum speed with maximum flow. It will continue to cycle automatically as the pressure increases. Only slight drops in outlet pressure or increase in air drive pressure will occur each cycle, thanks to very low frictional resistance.

Equilibrium

When the air drive force and output pressure are equal, the pump stops automatically. The pump will maintain pressure with zero energy consumption.

Media

  • Plain water
  • All hydraulic fluids
  • Distilled and di-ionized water
  • Solvents
  • Mild chemicals
  • Liquified CO2

Features

  • 316 Stainless Steel wetted hydraulic construction
  • Lightweight (6 lbs)
  • 3.5-inch x 7-inch body includes inlet and exhaust muffler
  • Hand pump attachment option


2. 10-4 Series Liquid Pumps

These are designed for high output capacity, easy maintenance, and wide ranges of operating pressures and output capacities.


Common applications:


Great for applications requiring extreme intermittent pressure, such as in water blasting.

General Information:

Air Drive

Require no electrical power. Powered by pressurized air, nitrogen vapor, or natural gas. The air
drive psi supplied is translated to output pressure using the pressure ratio. If the pressure ratio of the
pump is 30:1 and air drive pressure supplied is 50 psi, this means the output pressure is
approximately 1,500 psi. 
10-4 Series ratios available: 5:1, 10:1, 15:1, 30:1, 35:1, 55:1, 100:1, 140:1, 220:1, 300:1

  •         Starting air drive pressure: < 10 psi
  •         Max air drive pressure: 100 psi
  •         Max output pressure: 29,500 psig at 100 drive psi
  •         Volume Per Stroke: 0.047 – 2.59 in3
Modifications

     10-4 Series has one modification option available: model “A”. These use dual seals in the hydraulic assembly with a bleed-off between the seals to the atmosphere. This makes it easier to identify hydraulic seal leakage by providing a visual indication. One application for this may be where contamination of the air motor from the hydraulic fluid being pumped is undesirable.

3. 10-5 & D5 Series Liquid Pumps

     These pumps are similar to the 10-4. They may be mounted in any position, but vertical is preferred. A drain cock should be used to drain off any liquid that may accumulate in the pilot valve air chamber if mounted in another position. The D5 Series uses dry lubricant, so it does not require air lubrication. The 10-5 Series requires lubricated air.




General Information:
Air Drive

         Require no electrical power. Powered by pressurized air, nitrogen vapor, or natural gas. The air drive psi supplied is translated to output pressure using the pressure ratio. If the pressure ratio of the pump is 30:1 and air drive pressure supplied is 50 psi, this means the output pressure is approximately 1,500 psi. 


     10-5 & D5 Series ratios available: 5:1, 10:1, 12:1, 20:1, 25:1, 30:1, 35:1, 55:1, 70:1, 85:1, 105:1,140:1, 195:1, 280:1, 440:1, 555:1


         1.    Starting air drive pressure: < 10 psi
         2.    Max air drive pressure: 100 psi
         3.    Max output pressure: 55,000 psig at 100 drive psi. Intermittent duty above 30,000 psi.
         4.    Volume Per Stroke: 0.048 – 5.54 in3

Modifications

Six modification options are available.

       Model “A” uses dual seals in the hydraulic assembly with a bleed-off between the seals to the atmosphere. This makes it easier to identify hydraulic seal leakage by providing a visual indication. One application for this may be where contamination of the air motor from the hydraulic fluid being pumped is undesirable.

     Model “B” have a bottom inlet connection for tank top connection or alternate mounting configuration.

      Model “C” uses PTFE chevron packing in the hydraulic assembly. This provides maximum performance when other packing material is not compatible with the media or when used in extreme temperatures. Furthermore, the modification from Model “A” is included with PTFE O-rings.

       Model “H” uses special packing in the hydraulic assembly. It provides greater life expectancy from the hydraulic seals in situations where hydraulic fluid may by contaminated. Furthermore, the modification from Model “A” is included with PTFE O-rings.

        Model “K” uses a special air piston in the air motor assembly that decreases the stroke of the  pump. This decreases the internal forces and extends the life of the air motor. Great for  applications with rapid pressure drops, such as in burst testing.

         Model “R” uses an isolator attachment that prevents the hydraulic piston from retracting into     the air motor. This eliminates the possibility of contamination through the piston. It also acts as a heat barrier.

4. 10-6 & D6 Series Liquid Pumps

      These pumps are similar to the 10-5. They may be mounted in any position, but vertical is preferred. A drain cock should be used to drain off any liquid that may accumulate in the pilot valve air chamber if mounted in another position. The D6 Series uses dry lubricant, so it does not require air lubrication. The 10-6 Series requires lubricated air.



General Information:

Air Drive

        Require no electrical power. Powered by pressurized air, nitrogen vapor, or natural gas. The air drive psi supplied is translated to output pressure using the pressure ratio. If the pressure ratio of the pump is 35:1 and air drive pressure supplied is 50 psi, this means the output pressure is approximately 1,750 psi.

 10-6 & D6 Series ratios available: 5:1, 10:1, 20:1, 25:1, 35:1, 55:1, 95:1, 145:1, 180:1, 240:1,
330:1, 460:1, 740:1

         1. Starting air drive pressure: < 10 psi
         2. Max air drive pressure: 100 psi
         3. Max output pressure: 65,000 psig at 100 drive psi. Intermittent duty above 30,000 psi.
         4. Volume Per Stroke: 0.123 – 17.7 in3

Modifications

Six modification options are available.

      Model “A” uses dual seals in the hydraulic assembly with a bleed-off between the seals to atmosphere. This makes it easier to identify hydraulic seal leakage by providing a visual indication. One application for this may be where contamination of the air motor from the hydraulic fluid being pumped is undesirable.

     Model “B” have a bottom inlet connection for tank top connection or alternate mounting configuration.

      Model “C” uses PTFE chevron packing in the hydraulic assembly. This provides maximum performance when other packing material is not compatible with the media or when used in extreme temperatures. Furthermore, the modification from Model “A” is included with PTFE O-rings.

       Model “H” uses special packing in the hydraulic assembly. It provides greater life expectancy from the hydraulic seals in situations where hydraulic fluid may by contaminated. Furthermore, the modification from Model “A” is included with PTFE O-rings.

       Model “K” uses a special air piston in the air motor assembly that decreases the stroke of the pump. This decreases the internal forces and extends the life of the air motor. Great for applications with rapid pressure drops, such as in burst testing.

         Model “R” uses an isolator attachment that prevents the hydraulic piston from retracting intothe air motor. This eliminates the possibility of contamination through the piston. It also acts as a  heat barrier.

5. L6 Series High Volume Liquid Pumps

         These are great for high flow and high-pressure applications. Nominal outlet flow ranges from 1 gpm to 2 gpm. They are double acting, single stage compatible with most fluids and air operated. The parts are wetted stainless steel.

General Information:

Air Drive

        Require no electrical power. Powered by pressurized air, nitrogen vapor, or natural gas. The air drive psi supplied is translated to output pressure using the pressure ratio. If the pressure ratio of the pump is 40:1 and air drive pressure supplied is 50 psi, this means the output pressure is approximately 1,500 psi.

1. L6 Series ratios available: 40:1, 69:1, 115:1
         2. Max air drive pressure: 100 psig
         3. Max output pressure: 11,200 psig at 100 drive psi.
         4. Volume Per Stroke: 2.1 – 6.0 in3

Modifications

Two modification options are available. It is required to choose one.

       “Remote Pilot”: Provides a 1/8” NPT female port that can be used to remotely start and stop the pump. This can be done by connecting an external air signal to actuate the air cycling valve. This modification is the standard part number.

       “M014” - Counter Port: Provides a 5/8-18-UNF thread port on the air motor section of the pump  which can be used to install a mechanical cycle counter. This modification does not include the “Remote Pilot” option and changes part number to include “M014” at the end.

6. L10 Series Double Acting Liquid Pumps

        These are even better than the L6 Series for high flow and high-pressure applications. Nominal outlet flow ranges from 1 gpm to 3.5 gpm. They are double acting, compatible with most fluids and air operated. The parts are wetted stainless steel.


General Information:

Air Drive

      Require no electrical power. Powered by pressurized air, nitrogen vapor, or natural gas. The Airdrie psi supplied is translated to output pressure using the pressure ratio. See the table for pressure ratings.



           * Coned and threaded high-pressure connection for 20 KSI 9/16" O.D. tubing.
** Coned and threaded high-pressure connection for 30 or 60 KSI 9/16" O.D. tubing.


 1. L10 Series ratios available: 33:1, 64:1, 114:1
          2. Max air drive pressure: 100 psig
          3. Max output pressure: 25,600 psig at 100 drive psi.
          4.Volume Per Stroke: 2.15 – 16.84 in3


Modifications

Three modification options are available.

      “M002” - Remote Pilot: Provides a 1/8” NPT female port that can be used to remotely start and stop the pump. This can be done by connecting an external air signal to actuate the air cycling valve.

       “M014” - Counter Port: Provides a 5/8-18-UNF thread port on the air motor section of the pump which can be used to install a mechanical cycle counter.

      “M015” – High Pressure Outlet: Provides a 9/16 outer dimension tube outlet check valve port (13/16-16 UN female thread) rated for 20,000 psi.

7. SC Air Boosters and Systems

AB-2, AB-4, and AB-7 Compact Air Boosters


       These have a 4.5” x 5.4” x 7.4” compact design including the mount. Great for boosting your existing air pressure 2 to 4 times the line pressure up to 680 psig. Typically used in any low flow, high-pressure application, including clamping, holding, and leveling.

     The AB Series are single-acting, compact units. Inexpensive alternatives for applications   requiring low flow 100-680 psi. Their portability, economy, light weight, easy installation, and   no requirement for lubrication makes them a great option in OEM application. Remote pilot   modification is available.

Common applications:

General Information:

Air Drive

        Require no electrical power. Powered by pressurized air, nitrogen vapor, or natural gas. The air drive psi supplied is translated to output pressure using the pressure ratio. The air drive and supply are the same, so no extra plumbing is required.  If the pressure ratio of the pump is 7:1 and air drive pressure supplied is 50 psi, this means the output pressure is approximately 350 psi.

         1. AB-2, AB-4, and AB-7 ratios available: 1.7:1, 3.7:1, 7:1
         2. Max air drive pressure: 150 psi
         3. Max output pressure: 700 psi at 150 drive psi

Modifications

One modification option is available.

       “M202” - Remote Pilot: Provides a 1/8” NPT female port that can be used to remotely start and stop the pump. This can be done by connecting an external air signal to actuate the air cycling valve.

 8. ABD-2, ABD-2S & ABD-5 Series Air Boosters

        The advantage of the ABD Series over the AB Series is that they have high flow capacity and are double-acting, single stage. These are great if you have depleted your minimum air supply required for your system because you may connect the booster to your supply to achieve your required pressure. The volume from the booster should be enough for most equipment and the booster can be paralleled for more volume. Skip to “Air Booster Systems” if you require a separate tank or receiver. Take care that the speed does not exceed 40 cycles per minute. Reach out to gghyd.com if you need consultation. Common applications are similar to the AB series above.

General Information:

Air Drive

        Require no electrical power. Powered by pressurized air, nitrogen vapor, or natural gas. The air drive psi supplied is translated to output pressure using the pressure ratio. If the pressure ratio of the pump is 5:1 and air drive pressure supplied is 50 psi, this means the output pressure is approximately 250 psi.

         1. ABD-2, ABD-2S, and ABD-5 ratios available: 2:1, 5:1
         2. Max air drive pressure: 150 psi
         3. Max output pressure: 855 psi at 150 drive psi

Modifications

Eight modification options are available.

        “M202” - Remote Pilot: Provides a 1/8” NPT female port that can be used to remotely start and stop the pump. This can be done by connecting an external air signal to actuate the air cycling valve.

      “M205” – Cooling Jacket: “B” models have a bottom inlet connection for convenient tank top installation or alternate mounting configuration.

        “M200” – Refrigerant Recovery (2)

        “M201” - No Inlet / Outlet Plumbing (2)

        “M203” - No Inlet / Outlet Plumbing, Remote Pilot (2)

        “M204” - Cooling Jacket (2)

        “M206” - Cooling Jacket, No Inlet / Outlet Plumbing (2)
    
        “M207” - Cooling Jacket, No Inlet / Outlet Plumbing, Remote Pilot (2)

9. AB-2 & AB-4 Air Booster Systems

      These are the most compact sized air booster systems provided by SC Hydraulics. They are equipped with either an AB-2 or AB-4 booster along with a 200 cubic inch reservoir, high pressure gauge, filter/regulator combination with shut-off valve, air drive controls, and an air pressure gauge.  The components are mounted on a base plate.


      These are great in applications where the booster alone provides too little flow. The reservoir allows the booster to build up pressure between cycles. 

General Information:

Air Drive

        Require no electrical power. Powered by pressurized air, nitrogen vapor, or natural gas. The air drive psi supplied is translated to output pressure using the pressure ratio. If the pressure ratio of the pump is 4:1 and air drive pressure supplied is 50 psi, this means the output pressure is approximately 200 psi.

         1. AB-2 and AB-4 ratios available: 2:1, 4:1
         2. Max air drive pressure: 150 psi
         3. Max output pressure: 600 psi at 150 drive psi
         4. Dimensions: 18.25” x 12.5” x 6”
         5. Weight: approx. 35 lbs.

Modifications 

One modification option is available.

       “M202” - Remote Pilot: Provides a 1/8” NPT female port that can be used to remotely start and stop the pump. This can be done by connecting an external air signal to actuate the air cycling valve.

 10. ABD-2 Air Booster System

        This air booster system is made for high volume applications that may require up to 250 psi air reserve. A 15 gallon ASME receiver is attached to the double-acting 2:1 ratio ABD-2 air booster. 

        The unit is mounted on a heavy-duty skid with forklift provisions. It has receiver and regulator pressure gauges, a safety relief valve, and drive controls. This is a low-cost solution for high pressure and high-volume air applications.

General Information:

Air Drive

        Require no electrical power. Powered by pressurized air, nitrogen vapor, or natural gas. The air drive psi supplied is translated to output pressure using the pressure ratio. If the pressure ratio of the pump is 2:1 and air drive pressure supplied is 150 psi, this means the output pressure is approximately 300 psi.

          1. ABD-2 ratio available: 2:1
          2. Max air drive pressure: 150 psi
          3. Max output pressure: 300 psi at 150 drive psi
          4. Dimensions: 30” x 37.5” x 14”
          5. Weight: approx. 145 lbs.

Modifications

One modification option is available.

        “M202” - Remote Pilot: Provides a 1/8” NPT female port that can be used to remotely start and stop the pump. This can be done by connecting an external air signal to actuate the air cycling valve.

11. ABD-5 Air Booster System


         Similar to the ABD-2 Air Booster System but lighter and more powerful. This system utilizes a 5:1 ratio, double-acting, single-stage booster with a 600 psi ASME 5-gallon reservoir. It can be mounted horizontally or vertically. It includes an inlet filter/regulator with shut-off and gauge, muffler, safety relief valve, high pressure reservoir, outlet pressure gauges, and high-pressure regulator. Good for pressures up to 600 psi. 

General Information:

Air Drive

         Require no electrical power. Powered by pressurized air, nitrogen vapor, or natural gas. The Air drive psi supplied is translated to output pressure using the pressure ratio. If the pressure ratio of the pump is 5:1 and air drive pressure supplied is 50 psi, this means the output pressure is approximately 250 psi.

          1. ABD-5 ratio available: 5:1
          2. Max air drive pressure: 150 psi
          3. Max output pressure: 855 psi at 150 drive psi
          4. Dimensions: 22.25” x 21.5” x 24.16”
          5. Weight: approx. 85 lbs.

Modifications

Eight modification options are available.

       “M202” - Remote Pilot: Provides a 1/8” NPT female port that can be used to remotely start and stop the pump. This can be done by connecting an external air signal to actuate the air cycling valve.

       “M205” – Cooling Jacket, Remote Pilot: air cooling system to lower operating temperature in the high-pressure section.

        “M200” – Refrigerant Recovery

       “M201” - No Inlet / Outlet Plumbing

        “M203” - No Inlet / Outlet Plumbing, Remote Pilot

        “M204” - Cooling Jacket

       “M206” - Cooling Jacket, No Inlet / Outlet Plumbing

       “M207” - Cooling Jacket, No Inlet / Outlet Plumbing, Remote Pilot

12. SC Gas Boosters and Systems


        SC Hydraulic differentiates itself from competition with the speed to which it may custom build booster systems. Standard lead time for systems are 1-2 weeks. This can be expedited for a fee. Custom unit lead time typically runs 3-4 weeks which is less than half the time of other manufacturers. Other manufacturers will quote 6-8 weeks for a standard system.

      How is SC so much faster? Other manufacturers build many other systems. SC specializes in booster systems. They are not a large rigid company, but a medium flexible one. They work closely with each customer to satisfy their exact needs. In addition to this, SC manufactures the parts used in their units on-site. They do not depend on suppliers. Also, almost any booster they manufacture can be used in any system.

 GB Series Gas Booster Single Stage - Single Acting


      This series of gas boosters is SC’s smallest design. Great for pressurizing small volumes or pressure testing small components. The pressure chamber is hydrocarbon free. Can work with argon, helium, nitrogen, oxygen, hydrogen, and pressure as low as 50 psi. Flow can reach up to 14-SCFM. 


Common applications:


General Information:

Air Drive

         Require no electrical power. Powered by pressurized air. The air drive psi supplied is translated to output.


(1) Coned and threaded high-pressure connection for 1/4" O.D. tubing.
          Refer to the corresponding gas booster performance curve for operating pressures. Maximum material rated outlet pressures can be reached under special operating conditions. Do not use air drive and/or gas supply pressures that equate to higher outlet pressures than those "maximum material rated outlet pressures" shown on the table. Refer to Static Outlet Stall Pressure formula shown on a table (for example, for gas booster model GBD-30 the formula is: Static Outlet Stall Pressure = 30*Pa+Ps). Maximum recommended air drive operating pressure: 100-psi. Maximum rated air drive pressure: 150-psi (only for static outlet stall pressure).

        1. Lowest starting air drive pressure: 50 psi
        2. Max air drive pressure: 150 psi (only for static outlet stall pressure), otherwise 100 psi
        3. Max output pressure: 11,250 psi

Modifications

Two modification options are available.

       “M202” - Remote Pilot: Provides a 1/8” NPT female port that can be used to remotely start and stop the pump. This can be done by connecting an external air signal to actuate the air cycling valve.

       “M014” - Counter Port: Provides a 5/8-18-UNF thread port on the air motor section. Can be used to install a mechanical cycle counter.

Service Options:

13. GB-D Series Gas Booster Single Stage - Single Acting Double Head


       Identical to the above GB series, but has a double head that allows half the input pressure to achieve the same outlet pressure as the GB series. 


        Common applications are consistent with the GB series. In addition, the GB-D series is great for low flow, medium pressure applications. Nominal pressure can reach up to 15,000 psi. The high-pressure section is oil-free. Remote pilot control is possible with the modification.


Air Drive

        Require no electrical power. Powered by pressurized air. The air drive psi supplied is translated to output.



(1) Coned and threaded high-pressure connection for 1/4" O.D. tubing.
          Refer to the corresponding gas booster performance curve for operating pressures. Maximum material rated outlet pressures can be reached under special operating conditions. Do not use air drive and/or gas supply pressures that equate to higher outlet pressures than those "maximum material rated outlet pressures" shown on the table. Refer to Static Outlet Stall Pressure formula shown on the table (for example, for gas booster model GBD-30 the formula is: Static Outlet Stall Pressure = 30*Pa+Ps). Maximum recommended air drive operating pressure: 100-psi. Maximum rated air drive pressure: 150-psi (only for static outlet stall pressure).

        1. Maximum recommended air drive pressure: 100 psi
        2. Max output pressure: 20,000 psi
        3. Dimensions: 25.61” x 10.13” x 8.41”

Modifications

Two modification options are available.

       “M202” - Remote Pilot: Provides a 1/8” NPT female port that can be used to remotely start and stop the pump. This can be done by connecting an external air signal to actuate the air cycling valve.

       “M014” - Counter Port: Provides a 5/8-18-UNF thread port on the air motor section. Can be used to install a mechanical cycle counter.

Service Options:

14. GB Series and GB-D Series Double Acting Options:


Both of the above series have double acting options: GBD series and GBD-D series. 


GBD Series:




(1) Coned and threaded high-pressure connection for 1/4" O.D. tubing.

          Refer to corresponding gas booster performance curve for operating pressures. Maximum material rated outlet pressures can be reached under special operating conditions. Do not use air drive and/or gas supply pressures that equate to higher outlet pressures than those "maximum material rated outlet pressures" shown on table. Refer to Static Outlet Stall Pressure formula shown on table (for example, for gas booster model GBD-30 the formula is: Static Outlet Stall Pressure = 30*Pa+Ps). Maximum recommended air drive operating pressure: 100-psi. Maximum rated air drive pressure: 150-psi (only for static outlet stall pressure).

GBD-D Series:









(1) Coned and threaded high pressure connection for 1/4" O.D. tubing.
          Refer to corresponding gas booster performance curve for operating pressures. Maximum material rated outlet pressures can be reached under special operating conditions. Do not use air drive and/or gas supply pressures that equate to higher outlet pressures than those "maximum material rated outlet pressures" shown on table. Refer to Static Outlet Stall Pressure formula shown on table (for example, for gas booster model GBD-30 the formula is: Static Outlet Stall Pressure = 30*Pa+Ps). Maximum recommended air drive operating pressure: 100-psi. Maximum rated air drive pressure: 150-psi (only for static outlet stall pressure).

15. GBT Series Gas Booster Two Stage - Double Acting
         This gas booster is two-stage, double-acting. Good for high flow, medium pressure applications. Combining the first and second stages with a hydraulic piston allows for higher compression ratios. Nominal pressure can reach up to 12,500 psi. The high-pressure section is oil-free. Remote pilot control is possible with the modification.




        1. Maximum recommended air drive pressure: 100 psi
        2. Max output pressure: 20,000 psi
        3. Dimensions: 25.78” x 10.13” x 9.3”

Modifications

Two modification options are available.

       “M202” - Remote Pilot: Provides a 1/8” NPT female port that can be used to remotely start and stop the pump. This can be done by connecting an external air signal to actuate the air cycling valve.

       “M014” - Counter Port: Provides a 5/8-18-UNF thread port on the air motor section. Can be used to install a mechanical cycle counter.


Service Options: 


16. SC Power Units


30 Series Power Units

         This series is the most compact and lightweight of all 10 series pump power units offered by   SC. Installation is easy and everything is already mounted and connected on a base plate. Only   air, fluid supply, and work port connections are required to get the unit ready for use.

        There are two pressure ports on the unit. One is an air exhaust muffler to reduce noise, and the other is a shut-off or bleed valve. Furthermore, a liquid filled gauge made from stainless steel rated for 30,000 psi is provided. More gauge options are available for higher pressures.


Common applications:

Ordering Information:

       First, choose the pump you need for your application. Read our above section on 10 Series   Pumps for a detailed comparison. Technical specs are provided for each 30 Series power unit below.

       The 30-4 series uses a 10-4 pump, 30-5 series uses a 10-5 pump, and 30-6 series uses a 10-6 pump.

General Information:

Air Drive

        Require no electrical power. Powered by pressurized air, nitrogen vapor, or natural gas. The air drive psi supplied is translated to output pressure using the pressure ratio. If the pressure ratio of the pump is 30:1 and air drive pressure supplied is 50 psi, this means the output pressure is approximately 1,500 psi.

         A. Starting air drive pressure: < 10 psi
         B. Max air drive pressure: 100 psi

      Buna-Nitrile and Viton seals are available for the air motor section. Buna-Nitrile, EPR, and Fluorocarbon seals are available for the hydraulic section. Special seals may be requested if needed.

      Hydraulic section material can be constructed of aluminum bronze & stainless-steel alloy, or stainless steel, or cad plated carbon steel, stainless steel. Non-lubricated is standard, but lubricated is an option.




* Coned and threaded high pressure connection for ¼” O.D. tubing.
** Consult factory if gauge is desired.

Modifications:

Sixteen modification options are available.

"A" - "A" modification: Provides dual seals in the hydraulic section with a bleed-off. This provides a visual indication of seal leakage.

"B" - Bottom inlet (1): Provides a bottom inlet connection for tank installation or alternate mounting.
"D" - Bottom inlet - heavy duty.

"E" - Bottom inlet - "A" modification (1).

"G" - Isolator - heavy duty (1,3).

"H" - Heavy duty (1): Provides special packing in the hydraulic assembly for maximum performance where media is contaminated. This will achieve higher life expectancy than standard o-ring seals. “A” modification is included in “H” modification.

"J" - Bottom inlet - "K" modification (1).

"K" - "K" modification (1): Uses a special air piston in the  air motor assembly that lowers the stroke of the pump, reducing the internal forces. This will increase motor life. Good for applications with rapid pressure losses.

"M" - Bottom inlet - "A" and "K" modification (1).

"N" - Isolator - "A" modification (1).

"P" - Isolator - "K" modification (1).

"Q" - Isolator - "A" and "K" modification (1).

"R" - Isolator (1): Prevents the hydraulic piston from retracting into the motor, preventing contamination. The isolator is also a heat barrier.

"S" - Heavy duty - "K" modification (1,3).

"U" - Heavy duty - bottom inlet - "K" mod. (1,3).

"V" - Heavy duty - isolator - "K" modification (1,30).

90 Series Portable Test Cart


        The 90 series is a portable power unit. Works with all 10 series pumps and 100 psi air. Air drive controls, pressure gauges, valves, return line, pump hand attachment, and 5- or 10-gallon reservoir are included. Only two connections are required. Quiet operation with air exhaust muffler. Up to 65,000 psi.




        

  Common applications:

 Ordering Information:

       First, choose the pump you need for your application. Read our above section on 10 Series   Pumps for a detailed comparison. Technical specs are provided for each 90 Series power unit below.

       The 90-4 series uses a 10-4 pump the 90-5 uses a 10-5 pump and the 90-6 series uses a 10-6 pump. Next, choose the body material, see below.

  General Information:

  Air Drive

        Require no electrical power. Powered by pressurized air, nitrogen vapor, or natural gas. The air drive psi supplied is translated to output pressure using the pressure ratio. If the pressure ratio of the pump is 10:1 and air drive pressure supplied is 50 psi, this means the output pressure is approximately 500 psi.

      Buna-Nitrile and Viton seals are available for the air motor section. Buna-Nitrile, EPR, and Fluorocarbon seals are available for the hydraulic section. Special seals may be requested if needed.

   Body Material

      Hydraulic section material can be constructed of aluminum bronze & stainless-steel alloy, or stainless steel, or cad plated carbon steel, stainless steel. Non-lubricated is standard, but lubricated is an option.



 * Coned and threaded high pressure connection for 1/4" O.D. tubing.
** Consult factory if gauge is desired.
Modifications:

Eleven modification options are available.

"A" - "A" modification: Provides dual seals in the hydraulic section with a bleed-off. This provides a visual indication of seal leakage.

"B" - Bottom inlet (1): Provides a bottom inlet connection for tank installation or alternate mounting.

"G" - Isolator - heavy duty (1,3).

"H" - Heavy duty (1): Provides special packing in the hydraulic assembly for maximum performance where media is contaminated. This will achieve higher life expectancy than standard o-ring seals. “A” modification is included in “H” modification.

"K" - "K" modification (1): Uses a special air piston in the air motor assembly that lowers the stroke of the pump, reducing the internal forces. This will increase motor life. Good for applications with rapid pressure losses.

"N" - Isolator - "A" modification (1).

"P" - Isolator - "K" modification (1).

"Q" - Isolator - "A" and "K" modification (1).

"R" - Isolator (1): Prevents the hydraulic piston from retracting into the motor, preventing contamination. The isolator is also a heat barrier.

"S" - Heavy duty - "K" modification (1,3).

"V" - Heavy duty - isolator - "K" modification (1,30).

 L3 Series Power Units

       These are very low volume, lightweight power units. Read our section on L3 series pumps to seeif these will work for you. If you find that the L3 pump will work for you, you may integrate any of them with the below power units. 

S10011 L3 Tubular Power Units

          Weighs only 25 pounds, compact 18” wide x 19” high x 15” deep design, and includes a 1- or 2.2-gallon reservoir with fill cap and strainer. The reservoir is made of polyethylene to reduce the weight. Compatible with all L3 series standard pumps and includes air controls, shut-off, high-pressure gauge, manifold, bleed valve, and return line.


Common applications:

Ordering Information:

      First, choose the pump you need for your application. Read our above section on L3 Series Pumps for a detailed comparison. Use the ordering table below to create your power unit.

General Information:

Air Drive

         Require no electrical power. Powered by pressurized air, nitrogen vapor, or natural gas. The air drive psi supplied is translated to output pressure using the pressure ratio. If the pressure ratio of the pump is 20:1 and air drive pressure supplied is 50 psi, this means the output pressure is approximately 1,000 psi. A hand pump attachment option is available for precise pressure control or great for applications where shop air is not available.

         L3 & L3C ratios available: 20:1, 31:1, 40:1, 55:1, 79:1, 123:1, 133:1, 213:1

        1. Starting air drive pressure: < 15 psi
        2. Max air drive pressure: 125 psi (intermittent duty)
        3. Max output pressure: 24,375 psi at 125 drive psi, 1.0 gpm flow rate

Operation

      These pumps operate using the principle of differential areas. A small diameter hydraulic    plunger  is driven by an air piston and provides a pressure ratio that determines the maximum output pressure.

Cycle

       When air is first supplied to the pump, the pump will cycle at maximum speed with maximum flow. It will continue to cycle automatically as the pressure increases. Only slight drops in outlet pressure or increase in air drive pressure will occur each cycle, thanks to very low frictional resistance.

Equilibrium

         When the air drive force and output pressure are equal, the pump stops automatically. The pump will maintain pressure with zero energy consumption.

Media

·         Plain water
·         All hydraulic fluids
·         Distilled and di-ionized water
·         Solvents
·         Mild chemicals
·         Liquified CO2

Features

·         316 Stainless Steel wetted hydraulic construction
·         Lightweight (6 lbs)
·         3.5-inch x 7-inch body includes inlet and exhaust muffler
·         Hand pump attachment option

Ordering Table:




Notes:
        Additional Special Modifications may be included with an "M" suffix at the end of the model number.

Modifications:

Seven modification options are available.

       “M002” - Remote Pilot: Provides a 1/8” NPT female port that can be used to remotely start and stop the pump. This can be done by connecting an external air signal to actuate the air cycling valve.

       “M003” - SAE Straight Thread Ports: Provides SAE straight threads on the fluid inlet and outlet ports

       “M004” - Hand Pump Attachment: Provides a hand pump attachment great for precise testing or an emergency backup for pneumatic power

     “M005” - Distance Piece-Isolator: Provides an isolator attachment that prevents the hydraulic piston from retracting into the air drive, preventing contamination. The isolator is also a heat barrier.

      “M006” - No Air Piston Return Spring: Provides improved fill in the suction stroke when used with liquified gasses

   “M008” - Noise Reduction: Provides a special, internal bumper reducing noise without compromising power

        “M009” – 7/16”-20 x 1/4" High-Pressure Fitting Outlet: Provides a high-pressure fitting outlet


S10011 L3 Tank Mount Power Units

       Perfect for auxiliary hydraulic power for clamps, cylinders, etc. when volume is not a factor. Weighs only 5 pounds, compact 18” wide x 19” high x 15” deep design, and includes a 1-gallon reservoir. The reservoir is made of polyethylene to reduce the weight. Compatible with all L3 series standard pumps and includes air controls, high-pressure gauge, and return line. 


Common applications:

Ordering Information:

       First choose the pump you need for your application. Read our above section on L3 Series   Pumps for a detailed comparison. Use the ordering table below to create your power unit.

General Information:

Air Drive

        Require no electrical power. Powered by pressurized air, nitrogen vapor, or natural gas. The air drive psi supplied is translated to output pressure using the pressure ratio. If the pressure ratio of the pump is 20:1 and air drive pressure supplied is 50 psi, this means the output pressure is approximately 1,000 psi. A hand pump attachment option is available for precise pressure control or great for applications where shop air is not available.

        1. L3 & L3C ratios available: 20:1, 31:1, 40:1, 55:1, 79:1, 123:1, 133:1, 213:1
        2. Starting air drive pressure: < 15 psi
        3. Max air drive pressure: 125 psi (intermittent duty)
        4. Max output pressure: 24,375 psi at 125 drive psi, 1.0 gpm flow rate

Operation

        These pumps operate using the principle of differential areas. A small diameter hydraulic       plunger is driven by an air piston and provides a pressure ratio that determines the maximum output pressure.

Cycle

       When air is first supplied to the pump, the pump will cycle at maximum speed with maximum flow. It will continue to cycle automatically as the pressure increases. Only slight drops in outlet pressure or increase in air drive pressure will occur each cycle, thanks to very low frictional resistance.

Equilibrium 

         When the air drive force and output pressure are equal, the pump stops automatically. The pump will maintain pressure with zero energy consumption.

Media

·         Plain water
·         All hydraulic fluids
·         Distilled and di-ionized water
·         Solvents
·         Mild chemicals
·         Liquified CO2

Features

·         316 Stainless Steel wetted hydraulic construction
·         Lightweight (6 lbs)
·         3.5-inch x 7-inch body includes inlet and exhaust muffler
·         Hand pump attachment option

Ordering Table:



Modifications

Seven modification options are available.

      “M002” - Remote Pilot: Provides a 1/8” NPT female port that can be used to remotely start and stop the pump. This can be done by connecting an external air signal to actuate the air cycling valve.

      “M003” - SAE Straight Thread Ports: Provides SAE straight threads on the fluid inlet and outlet ports

       “M004” - Hand Pump Attachment: Provides a hand pump attachment great for precise testing or an emergency backup for pneumatic power

      “M005” - Distance Piece-Isolator: Provides an isolator attachment that prevents the hydraulic piston from retracting into the air drive, preventing contamination. The isolator is also a heat barrier.

       “M006” - No Air Piston Return Spring: Provides improved fill in the suction stroke when used with liquified gasses

   “M008” - Noise Reduction: Provides a special, internal bumper reducing noise without compromising power

      “M009” – 7/16”-20 x 1/4" High-Pressure Fitting Outlet: Provides a coned and threaded high-pressure connection for 20 KSI 1/4" O.D. tubing (7/16-20 thread LF4 connection)

S10014 L3 Base Mount Power Units


        This is the most basic design for use with L3 Series pumps. Weighs only 15-20 pounds, compact 9” wide x 10.5” high x 9” deep design, and does not include a reservoir. Compatible with all L3 series standard pumps and includes air controls, high-pressure gauge, pump, manifold and bleed valve. 


Common applications:

Ordering Information:

       First choose the pump you need for your application. Read our above section on L3 Series  Pumps for a detailed comparison. Use the ordering table below to create your power unit.

General  Information

Air Drive

       Require no electrical power. Powered by pressurized air, nitrogen vapor, or natural gas. The air drive psi supplied is translated to output pressure using the pressure ratio. If the pressure ratio of the pump is 20:1 and air drive pressure supplied is 50 psi, this means the output pressure is approximately 1,000 psi. A hand pump attachment option is available for precise pressure control or great for applications where shop air is not available. 


 1. L3 & L3C ratios available: 20:1, 31:1, 40:1, 55:1, 79:1, 123:1, 133:1, 213:1
 2. Starting air drive pressure: < 15 psi
 3. Max air drive pressure: 125 psi (intermittent duty)
 4. Max output pressure: 24,375 psi at 125 drive psi, 1.0 gpm flow rate

Operation

         These pumps operate using the principle of differential areas. A small diameter hydraulic plunger is driven by an air piston and provides a pressure ratio that determines the maximum output pressure.

Cycle

       When air is first supplied to the pump, the pump will cycle at maximum speed with maximum flow. It will continue to cycle automatically as the pressure increases. Only slight drops in outlet pressure or increase in air drive pressure will occur each cycle, thanks to very low frictional resistance.

Equilibrium

         When the air drive force and output pressure are equal, the pump stops automatically. The pump will maintain pressure with zero energy consumption.


Media

·         Plain water
·         All hydraulic fluids
·         Distilled and di-ionized water
·         Solvents
·         Mild chemicals
·         Liquified CO2

Features

·         316 Stainless Steel wetted hydraulic construction
·         Lightweight (6 lbs)
·         3.5-inch x 7-inch body includes inlet and exhaust muffler
·         Hand pump attachment option


Ordering Table:


Modifications

Seven modification options are available.

       
       “M002” - Remote Pilot: Provides a 1/8” NPT female port that can be used to remotely start and stop the pump. This can be done by connecting an external air signal to actuate the air cycling valve.

       “M003” - SAE Straight Thread Ports: Provides SAE straight threads on the fluid inlet and outlet ports

       “M004” - Hand Pump Attachment: Provides a hand pump attachment great for precise testing or an emergency backup for pneumatic power

     “M005” - Distance Piece-Isolator: Provides an isolator attachment that prevents the hydraulic piston from retracting into the air drive, preventing contamination. The isolator is also a heat
         barrier.

      “M006” - No Air Piston Return Spring: Provides improved fill in the suction stroke when used with liquified gasses

   “M008” - Noise Reduction: Provides a special, internal bumper reducing noise without compromising power

     “M009” – 7/16”-20 x 1/4" High-Pressure Fitting Outlet: Provides a coned and threaded high-pressure connection for 20 KSI 1/4" O.D. tubing (7/16-20 thread LF4 connection)



        Source : https://www.gghyd.com/blog/sc-hydraulic-engineering/

Friday, September 20, 2019

Best Hydraulic Solenoid Valve by GGHYD


The hydraulic solenoid valve has a cavity airtight with through-holes on different positions, each hole connects to different oil pipes. The plunger is in the middle of airtight, and two solenoids on both sides of the plunger. 

Once one of the solenoid coils is charged, the valve will move to the same side. In a word, the movement of the hydraulic solenoid is the key to start or close various oil outlets.

Indirect operated hydraulic solenoid valve (additionally called servo operated, or pilot operated) utilizes the differential weight of the medium over the valve ports to open and close. Generally, these valves need a base weight differential of around 0.5 bar. 

The bay and outlet are isolated by an elastic film, likewise called a stomach. The film has a little gap with the goal that the medium can stream to the upper compartment. The weight and supporting spring over the layer will guarantee that the valve stays shut. The cylinder over the film is associated with a little channel to the low weight port. This association is hindered in the shut position by a solenoid.

Read more about hydraulic solenoid valve

Tuesday, September 10, 2019

Parker Solenoid Coil 120v

The profitability limit is rather a merchant, we are a plant implying that the quality is completely constrained by us. Each parker solenoid coil 120v is reviewed completely from each angle before leaving the plant. For more data with respect to the quality review, it would be ideal if you visit our quality control page. 




We make in excess of 6 million bits of solenoid every year, which makes us a steady provider to our customers regardless of they are huge or little. We consider words from our customers important. That is the reason we have the majority of our items and our industrial facility affirmed by CE, UL, ISO, to give some examples. We never baffled any of our customers by quality, amount, cost or conveyance time.

The parker solenoid coil 120v quality generally remembers it that the nature of copper wire is so imperative to the curl that we just pick the best quality wire material. Our curl can work in a domain where the temperature is as high as 220 Celsius degree. The administration time can achieve 30,000 hours at most.

Read more about parker solenoid coil 120v




Wednesday, September 4, 2019

Best Hydraulic Solenoid Valve by GGHYD


Hydraulic Solenoid Valve


Our hydraulic power units aren't simply versatile, which is essentially significant on the off chance that you work in the field a ton. They are likewise manufactured intensely to withstand cruel working situations. The rough form quality stretches out to the cylindrical edge that encases the power units
.
The rounded edge is produced using cold moved rock-solid steel that is done in a hard-wearing powder covered paint. These across the board weight powerhouses are furnished with the standard water-powered framework staples just as a solid 7.5-liter water-powered liquid supply, air controls, drain valve, and a high weight check.

Hydraulic solenoid valve is used to control the flow of a variety of liquids and gases such as steam, water, air, nitrous, and oil. They are essential components of equipment used in the preparation and presentation of food products. They are also used in beverage dispensing equipment, commercial water coolers and draining devices incorporated into restaurant and cafeteria operations.

Solenoid valves are obtained in many of the sub-systems used to help in the control of a variety of vehicles. Solenoid valves are used on off-highway construction equipment, buses and trains as components in their braking, shifting and door opening/closing systems. They also assist in the portable refrigerant recovery equipment.

Read more about Hydraulic solenoid valve

Friday, August 23, 2019

Buy the Most Advanced Parker 12v Solenoid Coil by GGHYD


Solenoids are the most significant parts utilized in solenoid valves to control the progression of fluids and gases. Solenoids are electromechanical gadgets that convert AC or DC electrical vitality into direct movement. 

Parker 12v Solenoid Coil typically comprises a helical loop twisted concentrically around a versatile chamber, called the armature, produced using a ferromagnetic material, for example, iron or steel. Most solenoid valves have a replaceable curl and can be utilized with loops with various voltages. 


Parker 12v Solenoid Coil 


At the point when current courses through the loop, it produces an attractive field inside the curl which draws in the armature towards the focal point of the solenoid utilizing indistinguishable fundamental standards from customary electromagnets. 

Since the armature is drawn towards the focal point of the solenoid paying little respect to the extremity of the current, a contradicting power is expected to restore the armature into the beginning position when the curl isn't stimulated. This is accomplished by utilizing a spring instrument. Under perfect conditions, so as to activate the solenoid, the power created by the solenoid must be bigger than the consolidated powers of the spring, and the water driven weight, just as rubbing.

Read more about Parker 12v Solenoid Coil

Friday, August 9, 2019

Features Of Power Team Hydraulic Cylinder

Hydraulic cylinders are used to creating mechanical forces in linear motion.  The hydraulic cylinder is a tube capped at either end with a rod sticking out of one side. Attached to the rod inside the cylinder is a piston. GGHYD Power Team has its own range of cylinders that come in a large selection of sizes, offering a wide tonnage and stroke lengths.

The power team hydraulic cylinder are noted for their compact sizes, which belly their high-pressure output and breadth of applications.

Features Of Power Team Hydraulic Cylinder

  • A piston design that minimizes adverse effects from offset loading conditions

  • A seal band technology that lubricates the piston to reduce wear and tear.

  • A swivel cap that ensures safe and efficient operation, thanks to a visual indicator that shows when a load is centered and properly aligned.

  • POWER-TECH+ nitro carburization surface treatment, which is standard on select cylinders, protects cylinder components against frictional wear, abrasion, and corrosion. It also improves the impact and tensile strength.






Thursday, August 1, 2019

Find the Function and Construction Detail of Hydraulic Solenoid Valve



At a fundamental level, a hydraulic solenoid works comparably to an ordinary solenoid. An electromagnetically inductive loop is twisted around a metal center which makes a magnetic field when an electric flow goes through it. 

The magnetic field follows up on an armature and makes a mechanical power. The armature interfaces with a versatile component in the last application that requires situating. The essential contrasts between an electromechanical and hydraulic solenoid are the end capacity and development. 

Hydraulic Solenoid

Hydraulic Solenoid Function

The hydraulic solenoid valve is fundamentally utilized in Hydraulic pumps and valves. These solenoids can be intended to perform push, draw, or push/pull incitation capacities with either corresponding or on/off stroke qualities. 

Hydraulic Solenoid Construction

A hydraulic solenoid has 2 essential plan types. The first is the incorporated plan, which is the full solenoid unit as a solitary segment. This offers the most astounding exhibition however requires the framework to be depressurized when the solenoid should be supplanted. The second is the removable curl structure. 

This structure has a different cylinder which is introduced legitimately into the application, and afterward, the loop slides over the cylinder. A nut is utilized to tie down the loop to the cylinder. This structure takes into consideration the curl to be supplanted without additionally expelling the cylinder from the application, so the application can remain pressurized.

Read more about hydraulic solenoid valve